MADAS燃燒爐調壓閥,MADAS電廠配件
意大利MADAS馬達斯調壓閥是杠桿式壓差反饋控制調壓的。氣瓶里的燃氣是液態的,壓力太高,必須減壓才適合通往爐具燃燒。煤氣調壓閥壞了必須換新的。后果1,不出氣;后果2,不減壓。
不減壓,容易造成膠管脫落,泄漏燃氣,后果不堪設想。減壓原理:高壓介質通過一個小孔充到一個相對較大的腔里實現減壓,實際上是靠截流減壓。膜片或活塞的兩面一面是出口腔,一面是人為給的壓力,并且控制小孔大小的閥桿和膜片(活塞)相連。
馬達斯MADAS燃燒爐調壓閥氣體壓力調節器(高P2)
FRG / 2MCSH- RG / 2MCSH =沒有安全關閉裝置的濾波器調節器和調節器
FRG / 2MBH ... - RG / 2MBH ... =過濾調節器和帶安全關閉裝置的調節器
它可以配備以下安全裝置和配件:
出口過壓關閉裝置(僅2MBH ......版本):當調節器出口壓力上升到設備設定值時,它會停止氣流
安全閥:如果有下游調節器超壓,它會排出少量氣體。 如果安裝在通風不良的環境中,那么它在外面被排氣
出口低壓關閉裝置(僅2MBH ......版本):當調節器出口壓力下降到設備設定值時,它會停止氣流。 即使沒有入口壓力,它也會關閉。
出口壓力測試點。
入口過濾器(FRG / 2MBH ...- FRG / 2MCSH DN 15 - 20 - 25)
參考標準EN 88-2 - 334
MADAS燃燒爐調壓閥,MADAS電廠配件
GAS PRESSURE REGULATOR (HIGH P2)
FRG/2MCSH- RG/2MCSH= Filter regulators and Regulators without safety shut off device
FRG/2MBH... - RG/2MBH... = Filter regulators and Regulators with safety shut off device
It can be equipped with the following safety devices and accessory:
outlet over pressure shut off device (only 2MBH... versions): it stops the gas flow when the regulator outlet pressure goes up the device setting value
relief valve: it vents outside small quantity of gas in case there are downstream regulator overpressure. That exhaust it is convoyed outside in case of installation in environment with bad ventilation
outlet low pressure shut off device (only 2MBH... versions): it stops the gas flow when the regulator outlet pressure goes down the device setting value. It closes even if there is no inlet pressure.
outlet pressure test point.
inlet filter (only on FRG/2MBH...-FRG/2MCSH DN 15 - 20 - 25)
Reference standard EN 88-2 - 334
In conformity with:
2014/68/EU PED Directive
(ex 97/23/EC)
2014/34/EU ATEX Directive
(ex 94/9/EC)
MADAS燃燒爐調壓閥,MADAS電廠配件